SDH Fiber Problem

[mmzinyi at yahoo.com (jacob miller)]

Did so and am able to ping through

Regards,
Jacob Miller



----- Original Message -----
From: Leigh Porter <leigh.porter at ukbroadband.com>
To: jacob miller <mmzinyi at yahoo.com>
Cc: "nanog at nanog.org" <nanog at nanog.org>
Sent: Monday, September 19, 2011 12:23 PM
Subject: Re: SDH Fiber Problem

Did you try turning it off and on again? ;-)

-- 
Leigh Porter


On 19 Sep 2011, at 10:21, "jacob miller" <mmzinyi at yahoo.com> wrote:

> I have triend to do a ping with the DF bit set.
> Maximum am able to get to is 1600.
> This am guessing is because of the fact I have set the mtu size on My interface to 1600.
> 
> I have also enable all alarms on the node and am getting the following alarm which is registering as beign Minor.
> 
> "High Order Path Signal Label Mismatch"
> 
> Regards,
> jacob Miller
> 
> 
> 
> ----- Original Message -----
> From: Leigh Porter <leigh.porter at ukbroadband.com>
> To: jacob miller <mmzinyi at yahoo.com>
> Cc: "nanog at nanog.org" <nanog at nanog.org>
> Sent: Monday, September 19, 2011 11:17 AM
> Subject: Re: SDH Fiber Problem
> 
> It does sound like an MTU issue. Symptoms are typical. Did you try pings end to end with DF bit set and full size datagrams?
> 
> 
> 
> -- 
> Leigh Porter
> 
> 
> On 19 Sep 2011, at 09:15, "jacob miller" <mmzinyi at yahoo.com> wrote:
> 
>> By meanigful traffic I mean traffic like Http traffic
>> 
>> Am able to ssh no problem.
>> 
>> Most of the clients on the link are using it for browsing.
>> However we find that even though they are able to resolve and ping different sites.
>> When it comes to opening of the page we have the page reading as opening opening .. but the page never gets opened.
>> 
>> Regards,
>> Jacob Miller
>> 
>> 
>> 
>> ----- Original Message -----
>> From: Leigh Porter <leigh.porter at ukbroadband.com>
>> To: jacob miller <mmzinyi at yahoo.com>
>> Cc: "nanog at nanog.org" <nanog at nanog.org>
>> Sent: Monday, September 19, 2011 11:10 AM
>> Subject: Re: SDH Fiber Problem
>> 
>> What exactly do you mean by meaningful traffic? ICMP from port to port works, can you pass TCP? SSH between routers? Establish a TCP session over it?
>> 
>> Are you using Juniper SRXs ? :-)
>> 
>> -- 
>> Leigh Porter
>> 
>> 
>> On 19 Sep 2011, at 08:24, "jacob miller" <mmzinyi at yahoo.com> wrote:
>> 
>>> I have tried the pings and am able to ping through with a size of 1600 with the df-bit set
>>> 
>>> without the df-bit am able to get up to 9000.
>>> 
>>> The switched on bot ends hav been set to allow jumbo frames through and the system MTU size and routing MTU sizes are at 1998.
>>> The switch is a 2960 Cisco switch.
>>> 
>>> I have set the mtu on the interface on the end router to 1600 and still unable to push meaningful traffic.
>>> 
>>> Regards,
>>> jacob Miller
>>> 
>>> 
>>> 
>>> ----- Original Message -----
>>> From: Randy Bush <randy at psg.com>
>>> To: jacob miller <mmzinyi at yahoo.com>
>>> Cc: "nanog at nanog.org" <nanog at nanog.org>
>>> Sent: Monday, September 19, 2011 9:55 AM
>>> Subject: Re: SDH Fiber Problem
>>> 
>>>> I can ping on point to point
>>>> I have BGP up and running
>>>> When I try to pass traffic over the link my clients are unable to pass
>>>> any meanigful traffic asn browsing is impossible.
>>> 
>>> mtu?? try various size pings.
>>> 
>>> filters?
>>> 
>>> randy
>>> 
>>> 
>>> 
>>> ______________________________________________________________________
>>> This email has been scanned by the MessageLabs Email Security System.
>>> For more information please visit http://www.messagelabs.com/email
>>> ______________________________________________________________________
>> 
>> ______________________________________________________________________
>> This email has been scanned by the MessageLabs Email Security System.
>> For more information please visit http://www.messagelabs.com/email 
>> ______________________________________________________________________
>> 
>> 
>> 
>> ______________________________________________________________________
>> This email has been scanned by the MessageLabs Email Security System.
>> For more information please visit http://www.messagelabs.com/email 
>> ______________________________________________________________________
> 
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please visit http://www.messagelabs.com/email 
> ______________________________________________________________________
> 
> 
> 
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please visit http://www.messagelabs.com/email 
> ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email 
______________________________________________________________________